TEKTRON
Home Up Sensors Connectivity Bus Systems Signal Lights Wireless Control Machine Safety Ex-equipment About Us

Contact Us          Quality          Applications          Control Panels          Calibration Service                         email:  sales@tektron.ie               Tel: +353 (0)21 4313331
 

 

Up
DNet Bulk Cable
DNet JBs IP67
DNet JBs IP20
DNet FW Connect
DN CSets M8 1End
DN CSets M8 2End
DN CSets M12 1End
DN CSets M12 2End
DN CSets 7/8 1End
DN CSets 7/8 2End
DN DiagnosticConn
DN Bus Tees
DNet Receptacles
DN Couplers
DN ConduitAdapt
DN Term Resistor

 

 

 

 

 

DeviceNet™ 7/8" Cordsets

Connectors on Both Ends

As seen on our DeviceNet Bulk Cable page, there are over 20 types of DeviceNet cable. When combined with the different connector types, the result is quite a large range of cordsets. With connectors on both ends, the list of possible part numbers is too long to list here. Instead, the part number can be assembled using the matrix below. Standard lengths are 1M, 2M, 4M, 6M, 8M, 10M, 15M and in +5M increments for longer lengths available to order.   

For Stainless Steel Coupling Nuts change RKM to RKV, WKM to WKV, RSM to RSV, WSM to WSV                   

                    
Typical DeviceNet Cable            

7/8"  Connector Dimensions in Inches (millimetres)

       

         RKM Female Straight                             WKM Female Right-Angled   

 

       

        RSM Male Straight                               WSM Male Right-Angled         

Meaning of Type Codes

To use the matrix, select the connector on one end from the left columns. Select the connector on the other end from the rows along the top. Where the row and column intersect is the guide for the part number. All deviceNet cables begin with 57, so replacing the x, complete this number with the desired cable type. Replace the * with the length of cordset required in metres.

For example if a 6 metre cordset using Cable Type 5722B is required with a 7/8" Straight Male connector on one end and a 7/8" Female Right Angled connector on the other, the part number is RSM WKM 5722B-6M


7/8" - 7/8" Cordsets for DeviceNet

 

    Male Straight Male Right Angled Female Straight Female Right Angled
 

7/8"

 

       

7/8"

 

  RSM WSM RKM WKM

 

RSM RSM RSM 57x-*M RSM WSM 57x-*M RSM RKM 57x-*M RSM WKM 57x-*M


 

WSM   WSM WSM 57x-*M WSM RKM 57x-*M WSM WKM 57x-*M


 

RKM     RKM RKM 57x-*M RKM WKM 57x-*M


 

WKM       WKM WKM 57x-*M

Cable Types are HERE. Standard lengths are 1M, 2M, 4M, 6M, 8M, 10M, 15M and in +5M increments for longer lengths available to order.   

 

7/8" - M12 Reducing Cordsets for DeviceNet

These cordsets have 7/8" connector (left hand column) on one end and an M12 connector (top rows) on the other.

Note: When M12 connector is used only Mid and Thin types of cable can be used.

M12 Connector Dimensions in Inches (millimetres)

                         
         
       
RSC Male Straight M12                     WSC Male Right Angled M12

 

                     
          RKC Female Straight M12                  WKC Female Right Angled M12


 

    Male Straight Male Right Angled Female Straight Female Right Angled
 

M12

 

       

7/8"

 

  RSC WSC RKC WKC

 
Male Straight

RSM RSM RSC 57x-*M RSM WSC 57x-*M RSM RKC 57x-*M RSM WKC 57x-*M


Male Right Angled
 

WSM   WSM WSC 57x-*M WSM RKC 57x-*M WSM WKC 57x-*M


Female Straight
 

RKM     RKM RKC 57x-*M RKM WKC 57x-*M


Female Right Angled
 

WKM       WKM WKC 57x-*M

Cable Types are HERE. Standard lengths are 1M, 2M, 4M, 6M, 8M, 10M, 15M and in +5M increments for longer lengths available to order.